Maxview MXL002/TWIN Manual de instrucciones

abc MXL003 Seeker Wireless Installation & Operation Instruction Manual 9111403 Iss 1

10 Installation Required Tools & Equipment (not supplied) • 25mm-38mm hole saw • 2.5mm twist drill • Power Drill • No.2 Phillips screwdriver

11 Selecting an Installation Location Positioning the Antenna Unit • Check for obstructions such as roof lights and vents. • Check for electrical c

12 Attaching Antenna Mount Plate & LNB Park Plate 1. Remove antenna unit from wooden transit packaging. 2. Remove mounting plate from Antenna Un

Electrical Connections Whilst the adhesive is curing prepare the electrical connections for the Control Box requires a permanent 12v supply and a seco

14 Caravans Power can be taken directly from the leisure battery on the caravan. The ignition cable should be connected to the ignition key circuit wh

15 Attach Antenna Unit to Mounting Plate Carefully lower the antenna unit onto the Mounting Plate and re-attach the M6 Nuts and Washers that were pre

16 Installing Control Box Having previously chosen a suitable location 1. Clip the mounting brackets onto the Control Box. 2. Place Control Box on

17 Connection Diagram IGNITION Antenna Cable Satellite Cable Sa

18 Installing Control Panel Choose most suitable method of communication between Control Panel and Control Box. Wireless Mode 1. Install batteries i

19 Attach Satellite Dish to Antenna Unit 1. Ensure Antenna Unit is free from obstacles. 2. Press installation button on reverse of Control Box to e

2 Useful Information Date of Purchase Retailer Installer Serial Number

20 Operation Guide Installing Batteries Remove the battery door and insert 2 AA (LR6) batteries as shown. Take care to observe the correct polarity an

21 Pairing Control Panel and Control Box Every Control Panel made by Maxview contains a unique electronic identification number to prevent interferenc

22 Finding a Satellite Location & Set-up Before starting check there is a clear line of sight to the southern sky. All television broadcasting sat

23 Note: Search time is dependent on the change in elevation from last location. The Seeker will start the search routine from the last known elevati

24 Ignition Mode The ignition mode is a safety feature that automatically lowers the antenna and prevents accidental operation whilst travelling. Whe

25 Skew Adjustment Skew adjustment is required when signal strength is weak at the limit of a given satellites’ reception area. It involves adjusting

26 ASTRA 19.2 Caution Follow general safety advice on page 5 when adjusting Antenna Unit.

27 Software Update To keep your Seeker up to date with the latest satellites Maxview has incorporated a USB port on the front of the Control Box. The

28 Fault Finding Problem Actions Control Panel RF ERROR Move Control Panel closer to Control Box. Check Control Box power is on. Panel and box are

29 Specification MXL003/65 MXL003/85 Antenna Gain 36.0dB 38.1dB LNB Outputs 2 Wireless Frequency 868.3 MHz Wireless range 10 m Battery type

3 Contents Warranty ...

30 CE Declaration of Conformity The Seeker Wireless Satellite Antenna has been designed, constructed and marketed in compliance with safety requiremen

31 Reception Maps ASTRA 28.2E 2A/B North Beam 2A/B South Beam ASTRA 2D

32 ASTRA 19.2E 1KR 1L & 1M 1H HOTBIRD 13.0E

33 ASTRA 23.5E 3A 3B

34

4 Warranty Every new Ominsat Seeker Satellite System is thoroughly inspected and tested before leaving the factory, and is covered by the following tw

5 Safety Precautions Read this manual carefully and become familiar with your satellite antenna. Understand its applications, its limitations and any

6 Introduction Please read these instructions fully before using the antenna for the first time. The operation of the antenna has been designed to be

7 Control Box The Control Box requires wired connections for power, antenna control and satellite signal. It can be mounted discretely in a cupboard

8 Connections & Features Control Panel 1. Antenna Search button 2. Antenna Park button 3. Antenna position icon 4. Battery status icon 5.

9 Control Box Antenna Unit 1. Fuse 2. Power Switch 3. Power LED 4. Sync Button 5. Status LED 6. USB update port 7. LNB IN 8. LNB OUT 9.